Innovate-motorsports DL-32 Uživatelský manuál

DL32_Manual_1.3.doc DL-32 Multi-sensor Universal Data Logger User Manual

- 10 - To insert an SD card into the DL-32, push it into the SD card slot until it “clicks” in. To remove the SD card, push on it to “unclick” it.

- 11 - Alternatively you can start/stop recording with an XD-1/XD-16 chained to the serial OUT port of the DL-32. Pushbutton and Indicator LED oper

- 12 - A log window will be opened: Sessions are named “Session 1”, “Session 2”, etc. If a DL-32 session is too long for LogWorks (longer than 1-

- 13 - on a flat, horizontal, surface and press and hold all three buttons together until the display shows the letter ‘A’: After this, re-try t

- 14 - Input 4 Functions Function Indicator 1 2 3 4 F d = Functionality MAP (1 bar) (0..101.3 kPa) MAP (3 bar) (0..304.1 kPa) Vacuum (0..

- 15 - With pulsed signals the measured information is contained either in the frequency of a pulse train or the duty cycle of a pulse trains. Exam

- 16 - 7.1.2 Two-Stroke Engines On a 2-stroke engine there is a spark for every crank rotation, so the spark frequency doubles compared to a 4-stro

- 17 - - Determine the number of ignition pulses per crank rotation. Refer to Table 2 or 3 for guidance. - Press the ‘Channel’ button until it sho

- 18 - The inductive clamp measures the magnetic field created around a spark plug wire when spark current flows. If a metallic shield covers the sp

- 19 - 8. Measuring Pressures The DL-32 has a built in MAP sensor. To use it, connect a small ¼” hose between a vacuum/boost connection AFTER the t

- 2 - 1. Overview... 4

- 20 - can be up to 29.4 PSI above atmospheric pressure. Vacuum is typically measured here as negative PSI. But you can set up any metric you want w

- 21 - 11. Measuring external 5V sensors Each of the 5 channels on the DL-32 can be configured to accept input from an external 0..5V sensor. Hoo

- 22 - • Connect the ground from the external sensor supply to the GND connection on the DL-32 • Connect the +5V from the external sensor supply

- 23 - • Press the Channel button until the channel number to be calibrated is displayed • Press and hold the Calibrate button while the channel

- 24 - The LM Programmer software then shows in its first page the type and version number of the firmware of the device. 13.1 Changing the dev

- 25 - The drop-down list at the top of the window allows you to select the different functionality for that input. If RPM is selected, the area be

- 26 - 13.5.2 Measuring Frequency The center section of the window changes to this: You can enter any frequency between 10 Hz and 15000 Hz as

- 27 - Select if you use a drive-shaft sensor or a wheel sensor. Enter the pulses per rotation created by the sensor either as driveshaft rotation

- 28 - 14. Kit Contents DL-32 Kit P/N: 3782 Hardware Kit P/N: 3786 SD Memory Card P/N: 3787 R

- 29 - Appendix A: Limited Warranty LIMITED WARRANTY Innovate stands behind the quality of its products. Innovate makes the following warranty

- 3 - 13.7 Input 5 Configuration... 27 14. Kit Con

- 30 - Revision History 1.0 - 3/31/06 Initial Release 1.1 – 9/14/07 Added Kit Contents 1.2 – 2/20/08 Added terminator plug information

- 4 - 1. Overview The DL-32 is a data logger with 5 general purpose inputs. It can record these inputs on a SD memory card. In addition to its own

- 5 - pass it on. An example of a case where the command is executed but not passed on is the start-stop record command. The first upstream device c

- 6 - Devices attached to the LM-1’s analog input count as being part of the LM-1’s 6 channels. They don’t count extra. XD-16’s do not contribute

- 7 - As part of the DL-32 package you will have received a LED, a push-button switch, and a stereo 3.5mm cable with three stripped ends. The cable

- 8 - At the connection marked 5V you can connect external sensors. External sensors don’t HAVE to be powered by the DL-32. The 5V output is a conve

- 9 - Constantan wire of the probe. This extra junction will cause a large error in the temperature readings. Most Thermocouple probes are of the